Revised Improved Hellcat hunting rig and two standard ALICEs




OK I revised my Improved Hellcat pack, making it for a hunting rig, and moved the ALICE pack up to the top, and inserted a MSS bag that has a GI Intermediate Cold Weather sleeping bag (from the 80s, synthetic version of the M1949 mummy sleeping bag), and attached a gun scabbard to the right of the pack, and two canteens on the opposite to balance it out somewhat. I think this pack should be decent for hunting or target shooting, with a standard hunting carbine in the scabbard (SKS is inserted, but for hunting, it would have a flush 5 round magazine for Oregon State laws)


pack with MSS bag on bottom, SKS scabbard, and two canteens, along with filleting knife. I also added a webbing carry handle to the top, which also loops through the Tri-Glides of the load lifter straps so as to prevent accidentally undoing them.

DSCN1707view of the pack from the back; you can see how I moved the load lifter straps to the outboard top slots, and the webbing handle inserted through the same slots


view of the canteen side; the top canteen has a camelbak straw inserted into a canteen cap I modified by drilling a hole teeny bit smaller than the straw’s outside diameter, this allows a friction fit and prevents accidental leaks

DSCN1710the gun scabbard side, while there is room on the scabbard itself for pouches, I have decided not to put anything on the scabbard, so as to keep the balance of the load as reasonable as possible.

DSCN1713here, you can see the Improved Hellcat hunting rig between two standard  ALICE packs, the one on the left hand side has a green buttpack installed on the bottom, it is a mid 80s, early 90s ALICE MEDIUM pack. The other one on the far right, is a very early model, 1974 contract I believe, the buckles are cam/spring loaded friction buckles, and the fabric has faded quite significantly, it has two 2 qt canteens, one on each side, and a M1967 sleep carrier holding a camo compression sack.


you can see how the frames and the straps are different between the 3, the one on the Left, has the old style ALICE LC ruck straps, 2nd generation I believe with two quick releases rather than one like the 1st generation, the shoulder padding is short on this set, while the set on the one to the Right of the Hellcat are generally considered 3rd generation LC-2 straps, the padding on these are much longer, going from pack attachment all the way past the quick release hardware, it is similar to Tactical Tailor’s Super Straps, but without sternum straps. the kidney pads on the two Standard ALICE Mediums are missing belt portions, the one on the Right used to have a roll pin type of attachment for the belt webbing.

I might modify one of the standard ALICE packs to have Desert Camo MOLLE straps and belt, not sure which one yet.

Coleman Peak 1 framed Hellcat pack; Improved Hellcat

Acquired a vintage Coleman Peak 1 pack with frame; some of the hardware is damaged, and the pack fabric has some wear and tear and seems to be not as waterproof as it used to be; being 20 years old (ITW buckles have dates of 94 on them) ; So I decided to transfer my MOLLE and ALICE parts to the frame as a works without needing to be cut down like other PEAK 1 framed ALICE packs!



side by side of the front/frame side portions of both.



another view from the backDSCN1698

ALICE pack attached to unmodified PEAK 1 frame



front view, showing how the MOLLE components attach to the pack, I reused the PEAK 1 load lifter buckle straps, and used the MOLLE green straps to attach the ALICE pack to the frame in the slotted panelDSCN1700

ALICE lower pack attachment between Waist belt, which is also slotted into the side slotsDSCN1701

view from above, ALICE upper mounts, using the MOLLE short green load lifter strapsDSCN1702

PEAK load lifter straps in OEM positions, with the adjusting straps from the MOLLE shoulder straps threaded into the buckles.DSCN1706

SPEC OPS BRAND HUMP hydration pouch attached to the space between straps/belt and frame, using same slotted panelDSCN1705

lower strap attachment for MOLLE shoulder strapsDSCN1704

frame without pack, showing the geometry and the slotted panel in the center, the slots on the perimeter are ideal for lashing long items or cinch straps to reduce pack volumeDSCN1703


upper MOLLE shoulder strap centering straps slotted into two of the perimeter slots

Been busy….made a couple MOLLE versions, and got a friend whose site is up!

made 5 more pouches and shipped them out to beta testers; and finished 2 MOLLE versions a few days ago! now I just need to get more webbing; probably tomorrow, and then finish up the first batch of 15 pouches! also; will be making a few upsized pouches, at 5x5x3 and in MOLLE, possibly belt loops, for shotgun shell boxes,Jungle first aid kit plastic insert, AR15 20 round magazines, possibly AK 10rd magazines….we’ll see how they fit!

pictures of the MOLLE version, shown with USGI Army Medic pockets and mounted to Plate Carrier; the MOLLE version takes 3 MOLLE slots space on the plate carrier; and takes uh around 3 rows

and for my friend, Jon, his new site is up and running, it is all about guns and politics…feel free to join it!


copy and paste address below;